View FCP1206CXXXX-HX_558786.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Type FCP
Surface Mount Film Capacitors
Chip and SMT Capacitors
FCP Surface Mount Highlights:
* Capacitance Range of 100 pF to .22F * Standard EIA sizes 0603 thru 2416 * 16 and 50 Vdc Voltage Ratings
* Operating Temp. Range: -55 to 125 C
* Capacitance Change from -55C to 105C 1.5%
Type FCP stacked metallized polyphenylene sulfide (PPS) film capacitors offer high capacitance per unit volume, stable capacitance and D.F. over a wide temperature range, and excellent high frequency performance. Type FCP capacitors conform to standard EIA 0603, 0805, 1206, 1210, 1913 & 2416 surface mount case sizes and are packaged on tape and reel.
Specifications
Nominal Capacitance Range: 100 pF to 0.22 F (1 kHz at 5 Vrms) Capacitance Tolerance: 5% (J) Standard,2% (G) Optional Rated Voltage: 16 and 50 Vdc Dissipation Factor (Tan ): 0.6% Max. (1 kHz at 5 Vrms) Operating Temperature Range: -55C to +125C (See Voltage derating chart for .12 - .22 F above 105C) Dielectric Strength: 175% of rated Vdc for 5 seconds Insulation Resistance: 3000 M Min. at 20C, after 60 seconds. (16 Vdc rated, test 10 Vdc; 50 Vdc rated, test 50 Vdc) Construction: Stacked Metallized Polyphenylene Sulfide film.
www..com
CORNELL
1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: cdenb@cornell-dubilier.com
Life Test: Capacitors subjected to 1000 hours of maximum rated temperature and 125% of the rated voltage will not have any significant visual damage, the capacitance will be within 2% of the initial measured value, DF will be a maximum of 0.66%, and IR will be a minimum of 1000 Megohms. Moisture Resistance: Capacitors subjected to 1000 hours at 40C and 90% - 95% RH and rated voltage will not have any significant visual damage, will withstand 1.3 times the rated voltage for one minute, the capacitance will be within 2% of the initial measured value, DF will be a maximum of 0.9%, and IR will be a minimum of 1000 Megohms. Resistance to Soldering Heat: Capacitors subjected to a 260C reflow soldering for 5 seconds will not have any significant visual damage, dielectric strength will be as specified, the capacitance will be within 3% of the initial measured value, DF will be a maximum of 0.66%, and IR will be a minimum of 1000 Megohms.
www..com I E R DUBIL
Your Source For Capacitor Solutions
1.069
Chip and SMT Capacitors
Type FCP
Surface Mount Film Capacitors Ratings Table
Capacitance (F) 0.00010 0.00012 0.00015 0.00018 0.00022 0.00027 0.00033 0.00039 0.00047 0.00056 0.00068 0.00082 0.0010 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 (nF) 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120 150 180 220 (pF) 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000 120000 150000 180000 220000 16 Vdc CDE Part Number FCP0603C101J-K1 FCP0603C121J-K1 FCP0603C151J-K1 FCP0603C181J-K1 FCP0603C221J-K1 FCP0603C271J-K1 FCP0603C331J-K1 FCP0603C391J-K1 FCP0603C471J-K1 FCP0603C561J-K1 FCP0603C681J-K1 FCP0603C821J-K1 FCP0603C102J-K1 FCP0603C122J-K1 FCP0603C152J-K1 FCP0603C182J-K1 FCP0603C222J-K1 FCP0603C272J-K1 FCP0805C332J-J1 FCP0805C392J-J1 FCP0805C472J-J1 FCP0805C562J-J1 FCP0805C682J-J1 FCP0805C822J-J2 FCP0805C103J-J2 FCP1206C123J-H1 FCP1206C153J-H1 FCP1206C183J-H1 FCP1206C223J-H1 FCP1206C273J-H2 FCP1206C333J-H2 FCP1206C393J-H3 FCP1206C473J-H3 FCP1210C563J-G2 FCP1210C683J-G2 FCP1210C823J-G3 FCP1210C104J-G3 Case Code 50 Vdc CDE Part Number FCP0805H101J-J1 FCP0805H121J-J1 FCP0805H151J-J1 FCP0805H181J-J1 FCP0805H221J-J1 FCP0805H271J-J1 FCP0805H331J-J1 FCP0805H391J-J1 FCP0805H471J-J1 FCP0805H561J-J1 FCP0805H681J-J1 FCP0805H821J-J1 FCP0805H102J-J1 FCP0805H122J-J1 FCP0805H152J-J1 FCP0805H182J-J1 FCP0805H222J-J1 FCP0805H272J-J1 FCP1206H332J-H1 FCP1206H392J-H1 FCP1206H472J-H1 FCP1206H562J-H1 FCP1206H682J-H1 FCP1206H822J-H2 FCP1206H103J-H2 FCP1210H123J-G1 FCP1210H153J-G1 FCP1210H183J-G2 FCP1210H223J-G2 FCP1210H273J-G2 FCP1210H333J-G3 FCP1210H393J-G3 FCP1913H473J-E1 FCP1913H563J-E2 FCP1913H683J-E2 FCP1913H823J-E4 FCP1913H104J-E3 FCP2416H124J-D1 FCP2416H154J-D3 FCP2416H184J-D4 FCP2416H224J-D5 Case Code
0603
0805
0805
1206
1206
1210
1210
1913
2416
1.070
1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: cdenb@cornell-dubilier.com
CORNELL DUBILIER
Your Source For Capacitor Solutions
Type FCP
Surface Mount Film Capacitors
Typical Temperature Characteristics
Capacitance Change
3 2 10 8 6 4 2 0 -2 -4 -6 -8 -10 1 10 100 1000 10000
Chip and SMT Capacitors
Typical Frequency Characteristics
Capacitance Change
C/C (%)
0 -1 -2 -3 -60 -40 -20 0 20 40 60 80 100 120 140
C/C (%)
1
Temperature (C)
Frequency (kHz)
Dissipation Factor
0.6
Dissipation Factor
10 9 8 7 6 5 4 3 2 1 0 1 10 100 1000
.01 F
(%)
0.4
0.2
0 -60 -40 -20 0 20 40 60 80 100 120 140
Tan (%)
Tan
10000
Temperature (C)
Frequency (kHz)
Insulation Resistance
10,000
100.00
Im pedance
0.0082 F
1000 Megohms
1,000
10.00
100
Ohms
1.00
10 -60 -40 -20 0 20 40 60 80 100 120 140
0.10 1 10 100
Temperature (C)
Frequency (MHz)
CORNELL DUBILIER
Your Source For Capacitor Solutions
1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: cdenb@cornell-dubilier.com
1.071
Chip and SMT Capacitors
Type FCP
Surface Mount Film Capacitors Outline Dimensions
L W T
t t
Case Size Code 0603 0805 1206
Outline Dimensions (in.) L0.008 0.063 0.079 0.126 W T0.008 t 0.0140.008 0.0180.010 0.0260.012 0.0320.006 0.0280.006 0.035 0.0490.008 0.043 0.035 0.0630.008 0.043 0.059 0.043 0.0980.008 0.059 0.083 0.055 0.079 0.1300.012 0.110 0.094 0.071 0.094 0.1610.012 0.110 0.126
Outline Dimensions (mm) Case Size (metric) L0.2 W T0.2 t 1608 2012 3216 1.6 2.0 3.2 0.800.15 0.70.15 0.350.2 0.9 1.250.2 0.450.25 1.1 0.9 1.60.2 0.650.3 1.1 1.5 1.1 2.50.2 0.650.3 1.5 2.1 1.4 2.0 3.30.3 0.350.2 2.8 2.4 1.8 2.4 4.10.3 0.350.2 2.8 3.2
Packaging Code K1 J1 J2 H1 H2 H3 G1 G2 G3 E1 E2 E3 E4 D1 D3 D4 D5
1210
0.126
0.0260.012
3225
3.2
1913
0.189
0.0140.008
4833
4.8
2416
0.236
0.0140.008
6041
6.0
Pulse Handling Capability
Capacitance (F) 0.0001 0.00012 0.00015 0.00018 0.00022 0.00027 0.00033 0.00039 0.00047 0.00056 0.00068 0.00082 0.001 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 Voltage (Vdc) 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 dV/dt (volts/sec) 420 390 350 325 295 270 245 225 205 193 175 160 150 135 123 115 105 95 86 80 74 68 62 58 Capacitance (F) 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.0001 0.00012 0.00015 0.00018 0.00022 0.00027 0.00033 0.00039 0.00047 0.00056 0.00068 Voltage (Vdc) 16 16 16 16 16 16 16 16 16 16 16 16 16 50 50 50 50 50 50 50 50 50 50 50 dV/dt Capacitance (volts/sec) (F) 52 48 43 40 37 33 31 28 26 24 22 20 19 1100 1050 940 890 800 730 690 610 580 520 480 0.00082 0.001 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 .047 - 0.1 0.12 - 0.22 Voltage (Vdc) 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 dV/dt (volts/sec) 440 400 370 340 310 270 260 240 220 200 190 170 160 145 135 120 110 100 94 86 78 180 130
1.072
1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: cdenb@cornell-dubilier.com
CORNELL DUBILIER
Your Source For Capacitor Solutions
Type FCP
Surface Mount Film Capacitors
Voltage Derating vs. Temperature
120
Chip and SMT Capacitors
Percentage of Rated Voltage (%)
FCP 100 pF - 0.1F
100 80 60 40 20 0 -60 -40 -20 0 20 40 60 80 100 120 140
FCP (0.12F - 0.22F@50 Vdc)
If the temperature on the surface of the capacitor is above 105C, then the maximum voltage for FCP 50 Vdc ratings from .12 F to .22F must be derated linearly from full rated voltage at 105C to 75% of the rated voltage at 125C.
Temperature (C)
Vrms vs. Frequency
Maximum AC Voltage FCP 16 Vdc Series
100
Maximum AC Voltage FCP 50 Vdc Series
100
40 Vrms 30 Vrms
Vrms
Vrms 11 Vrms 10 100 pF - 0.1 F
0.0018 F 0.01 F
10
0.039 F 0.1 F
100 pF - 0.039 F: 30 Vrms Max. 0.047 F - 0.22 F: 40 Vrms Max.
0.22 F
1 10 100 Frequency (kHz) 1000
1 10 100 Frequency (kHz) 1
The capacitor surface temperature should not exceed 125C.
Typical Applications
Resonant Circuit for Inverter: Liquid Crystal Display Panel Higher efficiency in battery operated devices.
Dissipation Factor(loss) vs. Frequency
6
FCP
4
D.F. (%)
DC / DC Converter
MLCC X7R/0.1F FCP 0.1F
2
0 1 10 100 1000 10000
Frequency (kHz)
Very low losses and stable temperature characteristics make film chip capacitors the best choice for resonant circuit applications.
CORNELL DUBILIER
Your Source For Capacitor Solutions
1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: cdenb@cornell-dubilier.com
1.073
Chip and SMT Capacitors
Type FCP
Surface Mount Film Capacitors Typical Applications
Filtering Capacitor for xDSL:
Telephone Line Impedance vs. Frequency (Typical Performance FCP Series)
100
FCN 250 V 400 V
FCP FCP
FCP
Impednace (Ohms)
10
1
0.1
0.0033F 0.01F 0.1F
FCP
0.01 1 10 100 1000 10000
Frequency (MHz)
Capacitance Change vs. Bias Voltage
2
Capacitance Change vs. Temperature
5
Capacitance Change (%)
Capaciance Cange (%)
0
0 -5 -10 -15 -20
-2
FCP PPS Film Capacitor .010 F MLCC X7R 0.01F
FCP 0.01 F
-4
MLCC X7R 0.01F
-6 -20 -10 0 10 20
-60
-40
-20
0
20
40
60
80
100 120 140
Bias Voltge (Vdc)
Temperature (C)
The capacitance of SMT film chips is much more stable with applied voltage and with changes in temperature than multilayer ceramic capacitors. Add in the low e.s.r. characteristics of film chips and the final result is improved performance in filter circuit applications.
PLL Circuit:
Tantalum
Cellular phone, Blue Tooth, Data Communication Cards Loop Filter Charge Pump VCO
Lock-up Time
MLCC X7R FCP
0 100 200 300 400 500
FCP
Time (s)
FCP
In PLL circuit applications, FCP SMT film capacitor advantages are tight tolerance on the capacitance value, stable capacitance with temperature, faster lock-up times, and no noise due to piezoelectric effects
1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: cdenb@cornell-dubilier.com
CORNELL DUBILIER
Your Source For Capacitor Solutions
1.074
Chip and SMT Capacitors
Application Guide, Film Chip Capacitors
Reel Quantity and Dimensions
Packaging Code K1 J1, J2 H1, H2 H3 G1, G2, G3 E1, E2 E3, E4 D1, D2 D3, D4, D5 B, Z U, V, X, Y S, T
Tape Width [mm] 8 8 8 8 8 12 12 12 12 12 16 24
Reel Diameter [in.(mm)] 7 (178) 7 (178) 7 (178) 7 (178) 7 (178) 13 (330) 13 (330) 13 (330) 13 (330) 13 (330) 13 (330) 13 (330)
Quantity/Reel 4000 3000 3000 2000 2000 3000 2000 3000 2000 1500 1000 750
Symbol A C D E N r W1 W2
8 mm Tape 178 13 21 2 60 1 9.5 1.2
Reel Dimensions (mm) 12 mm Tape 16 mm Tape 330 330 13 13 21 21 2 80 80 1 14 17.5 2 -
24 mm Tape 330 13 21 80 25.5 -
Tape Dimensions
(mm)
Type K1 J1 J2 H1, H2 H3 G1, G2 G3 E1 E2 E3, E4 D1 D3, D4 D5 B Z X, Y U, V S, T
A 0.1 1.0 1.55 1.55 1.9 1.9 2.8 2.8 3.8 3.8 3.8 4.6 4.6 4.6 5.5 5.5 6.91 8.94 10.8
B 0.1 1.85 2.3 2.3 3.5 3.5 3.5 3.5 5.1 5.1 5.1 6.3 6.3 6.3 6.3 7.5 8.43 10.54 16.0
T 0.05 0.2 0.25 0.25 0.25 0.25 0.25 0.25 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.34.02 0.34.02 0.36.02
T2 0.2 1.1 1.3 1.5 1.5 1.9 1.9 2.5 2.0 2.6 3.4 2.7 3.5 4.6 5.1 4.7 5.69 5.8 5.82
K 0.1 1.0 1.2 1.4 1.4 1.8 1.8 2.4 1.9 2.5 3.5 2.6 3.4 4.5 5.0 4.6 5.64 5.75 5.77
Tape Dimensions (mm) Symbol W F E P1 P2 P0 D0 D1 K1 8 3.5 1.75 2 4 1.5 J1,J2, H1,H2,H3,G1,G2,G3 8 3.5 1.75 4 2 4 1.5 1 E1, E2 E3, E4 12 5.5 1.75 8 2 4 1.5 1.5 D1, D2, D3, D4, D5, B, Z 12 5.5 1.75 8 2 4 1.5 U, V X, Y 16 7.5 1.75 12 2 4 1.5 1.5 S, T 24 11.5 1.75 16 2 4 1.5 1.5
1.080
1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: cdenb@cornell-dubilier.com
CORNELL DUBILIER
Your Source For Capacitor Solutions
Application Guide, Film Chip Capacitors
Recommended Land Patterns
Capacitor Outline Land Land
C
Case Size Code 0603 0805 1206 1210 1913 2416 2420 2820 2825 3022 3925 3931 6031 6040 Land Dimensions [in.(mm)] A 0.024 0.03 0.07 0.07 0.10 0.15 0.15 0.18 0.18 0.20 0.28 0.28 0.50 0.50 (0.6) (0.8) (1.8) (1.8) (2.6) (3.8) (3.8) (4.5) (4.5) (5.1) (7.2) (7.2) (12.6) (12.6) B 0.08 0.09 0.14 0.14 0.26 0.31 0.31 0.35 0.35 0.38 0.47 0.47 0.68 0.68 (2.0) (2.4) (3.6) (3.6) (6.6) (7.8) (7.8) (9.0) (9.0) (9.7) (11.9) (11.9) (17.3) (17.3) C 0.028 0.04 0.06 0.09 0.12 0.15 0.18 0.18 0.22 0.20 0.22 0.28 0.28 0.35 (0.7) (1.1) (1.4) (2.3) (3.0) (3.8) (4.6) (4.6) (5.7) (5.0) (5.7) (7.2) (7.2) (9.0)
Chip and SMT Capacitors
A B
Soldering Information
Recommended Reflow Soldering Conditions
Soldering Reflow method only, not to exceed two reflow processings. Halogen content of flux, solder paste and cleaner should be less than 0.1% for each.
Peak Temperature
Cleaning Solvent Isopropyl alcohol
Cleaning Method Temperature Immersion 25C Vapor <50C Ultrasonic <50C
Time <5min. <5min. <5min.
Capacitor Type FCN 16 V, 50 V, 100 V (.001 - .01 F) FCN 100 V (.012 - 1.0 F), 250 V, 400 V FCP FCA
Dry the circuit board completely after cleaning.
Maximum Capacitor Surface Temperature (C) 240 230 260 240
Recommended Peak Reflow Temperature (C) 230 220 230 230
Maximum 30 Seconds at or above (C) 210 210 230 210
Ordering Information
Type FCN Case Size 1913 Voltage Code C
C = 16 Vdc H = 50 Vdc A = 100 Vdc E = 250 Vdc G = 400 Vdc
Capacitance Code 124
124 = 120000 pF = .12 F
Tolerance Code J
J= 5% K = 10 %
-
Packaging Code E1
FCP
1206
C
C = 16 Vdc H = 50 Vdc
393
393 = 39000 pF = .039 F
J
J= 5% G= 2%
H3
FCA
1206
A
A = 10 Vdc C = 16 Vdc
105
105 = 1000000 pF = 1.0 F
M
M = 20 %
H3
(See Reel Quantity Table for an explanation of the Packaging Code)
CORNELL DUBILIER
Your Source For Capacitor Solutions
1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: cdenb@cornell-dubilier.com
1.081
Chip and SMT Capacitors
Application Guide, Film Chip Capacitors
Available Surface Mount Film Capacitor Ratings
pF Code 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 Capacitance pF 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000 120000 150000 180000 220000 270000 330000 390000 470000 560000 680000 820000 1000000 nF 0.1 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 F 0.0001 0.00012 0.00015 0.00018 0.00022 0.00027 0.00033 0.00039 0.00047 0.00056 0.00068 0.00082 0.001 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1 16 V 50 V FCN 100 V 250 V 400 V FCP 16 V 50 V FCA 10 V 16 V
0603
0805
1206 1913
1913 1210
0805
1206
2416 1206 1913 2416 2825 1913 2420 2416 1913 2416 2820 3925 2416 3022 3931 6031 3925 6040 1206 2825 3925 3931 2416 1210 1913 0805 1206 1206 1206 1206 1206 1210 2420 2820 1210
1.082
1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: cdenb@cornell-dubilier.com
CORNELL DUBILIER
Your Source For Capacitor Solutions

▲Up To Search▲

Price & Availability of FCP1206CXXXX-HX

	To Download FCP1206CXXXX-HX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .